奇狐社區論壇

奇狐社區論壇 : Powered by vBulletin version 2.3.0

奇狐社區論壇 > 指標公式 > 問題交流 > 請教

上一主題下一主題

作者

主題

tsh
資深會員

註冊日期: Feb 2016
來　　自:
文章數量: 220

請教

MA5:MA(CLOSE,P1),COLORBROWN,Linethick1;
MA10:MA(CLOSE,P2),ColorRED,Linethick1;
MA20:MA(CLOSE,P3),COLORBLUE,Linethick1;
MA65:MA(CLOSE,P4),ColorFFCC66,Linethick1;
ma24:=ma(c,24);
ma48:=ma(c,48);
C1:=ma(close,5)<REF(ma(close,5),1) AND REF(ma(close,5),1)>=REF(ma(close,5),2);
C2:=ma(close,5)>REF(ma(close,5),1) AND REF(ma(close,5),1)<=REF(ma(close,5),2);
c3:=ma(close,5)>ma(close,10) AND REF(ma(close,5)<=ma(close,10),1);
C4:=ma(close,5)<ma(close,10) AND REF(ma(close,5)>=ma(close,10),1);
c5:=ma(close,5)>ref(ma(close,5),1) and ma(close,10)>ref(ma(close,10),1) and ma(close,20)>ref(ma(close,20),1);
c6:=ma(close,5)<ref(ma(close,5),1) and ma(close,10)<ref(ma(close,10),1) and ma(close,20)<ref(ma(close,20),1);
DRAWICON(C1,h,9)pxup20;
DRAWICON(C2,l,8)pxdn20;
DRAWICON(C3,h,'$SA-A2-2Bt.gif'),align4;
DRAWICON(C4,h,'$SA-A2-2St.gif'),align4;
DRAWICON(C5,h,8),align5;
DRAWICON(C6,h,9),align5;

請教版主，若更改ｐ１到p5任一值時會出現下列訊號，但若先執行系統ma程式再更改自訂程式的參數就沒問題．不知是哪裡有問題，謝謝！！

tsh 附帶上了此圖片:

向版主報告此篇 |

2021-01-13 10:08

cutgg
資深會員

註冊日期: Apr 2009
來　　自:
文章數量: 809

回覆: 請教

引用:
最初由 tsh 發表
MA5:MA(CLOSE,P1),COLORBROWN,Linethick1;
MA10:MA(CLOSE,P2),ColorRED,Linethick1;
MA20:MA(CLOSE,P3),COLORBLUE,Linethick1;
MA65:MA(CLOSE,P4),ColorFFCC66,Linethick1;
ma24:=ma(c,24);
ma48:=ma(c,48);
C1:=ma(close,5)<REF(ma(close,5),1) AND REF(ma(close,5),1)>=REF(ma(close,5),2);
C2:=ma(close,5)>REF(ma(close,5),1) AND REF(ma(close,5),1)<=REF(ma(close,5),2);
c3:=ma(close,5)>ma(close,10) AND REF(ma(close,5)<=ma(close,10),1);
C4:=ma(close,5)<ma(close,10) AND REF(ma(close,5)>=ma(close,10),1);
c5:=ma(close,5)>ref(ma(close,5),1) and ma(close,10)>ref(ma(close,10),1) and ma(close,20)>ref(ma(close,20),1);
c6:=ma(close,5)<ref(ma(close,5),1) and ma(close,10)<ref(ma(close,10),1) and ma(close,20)<ref(ma(close,20),1);
DRAWICON(C1,h,9)pxup20;
DRAWICON(C2,l,8)pxdn20;
DRAWICON(C3,h,'$SA-A2-2Bt.gif'),align4;
DRAWICON(C4,h,'$SA-A2-2St.gif'),align4;
DRAWICON(C5,h,8),align5;
DRAWICON(C6,h,9),align5;

請教版主，若更改ｐ１到p5任一值時會出現下列訊號，但若先執行系統ma程式再更改自訂程式的參數就沒問題．不知是哪裡有問題，謝謝！！