|
引用:
最初由 cgjj 發表
看不是很懂, 可作圖說明嗎?
1:所附源碼CA是金叉的收盤價,可以正常顯示.
2:所以四個值皆為金叉的收盤價而成一列.
3:源碼要顯出兩列
一列SYSPARAM(5)*0.977
另一SYSPARAM(5)-SYSPARAM(5)/21
4:今只顯出一列而已,是不是條件的問題?
5:"KISS@BACK"為了其他用途不得不用.
煩請幫忙指導修改 謝謝
RSV:=(CLOSE-LLV(LOW,9))/(HHV(HIGH,9)-LLV(LOW,9))*100;
K:=SMA(RSV,3,1);
D:=SMA(K,3,1);
A:=CROSS(K,D);
B:=CROSS(D,K);
ZA:=BARSLAST(A);
ZB:=BARSLAST(B);
DRAWICON(A,L*0.975,4);
DRAWICON(B,H*1.025,5);
CA:REF(C,ZA),PRECISION0,COLORRED,Linethick0;
M:=BARSCOUNT(C);
G:=SYSPARAM(2)=M;
E1:="KISS@BACK"(REF(CA,BARSLAST(SYSPARAM(1)=M)));
E:=ROUND(E1);
DRAWTEXT(REF(G,50),SYSPARAM(5)*0.977,'值:'),Align5,colorred;
DRAWTEXT(REF(G,70),SYSPARAM(5)*0.977,'值:'),Align5,colorred;
DRAWTEXT(REF(G,90),SYSPARAM(5)*0.977,'值:'),Align5,colorred;
DRAWTEXT(REF(G,110),SYSPARAM(5)*0.977,'值:'),Align5,colorred;
DRAWNUMBER(REF(G,55),SYSPARAM(5)*0.977,E,0),Align5;
DRAWNUMBER(REF(G,75),SYSPARAM(5)*0.977,E,0),Align5;
DRAWNUMBER(REF(G,95),SYSPARAM(5)*0.977,E,0),Align5;
DRAWNUMBER(REF(G,115),SYSPARAM(5)*0.977,E,0),Align5;
DRAWTEXT(REF(G,50),SYSPARAM(5)-SYSPARAM(5)/21,'值:'),Align5,colorred;
DRAWTEXT(REF(G,70),SYSPARAM(5)-SYSPARAM(5)/21,'值:'),Align5,colorred;
DRAWTEXT(REF(G,90),SYSPARAM(5)-SYSPARAM(5)/21,'值:'),Align5,colorred;
DRAWTEXT(REF(G,110),SYSPARAM(5)-SYSPARAM(5)/21,'值:'),Align5,colorred;
DRAWNUMBER(REF(G,55),SYSPARAM(5)-SYSPARAM(5)/21,E,0),colorGREEN,Align5;
DRAWNUMBER(REF(G,75),SYSPARAM(5)-SYSPARAM(5)/21,E,0),Align5;
DRAWNUMBER(REF(G,95),SYSPARAM(5)-SYSPARAM(5)/21,E,0),Align5;
DRAWNUMBER(REF(G,115),SYSPARAM(5)-SYSPARAM(5)/21,E,0),Align5;
|
2004-11-02 22:06
